- PU Primer
- 283-322 Urethane White PU Pigmented Primer
- Codes de produit:
283-322
- Surface Preparation: Substrate should be sanded with 120, 150 or 180 grit sandpaper prior to finishing. Difficult or oily substrates may require the use of 401-033 Isolante sealer prior to priming to ensure maximum adhesion.
- General Information:
Agitate before use, and while adding hardener and solvent as per mixing ratio. To ensure product consistency, the mixed material should be agitated at all times. When cured, P.U. Primer White must be sanded to be recoated within eight hours of sanding.
The relative humidity in the application and drying rooms should never exceed 75%. Viscosity on the catalyzed material should be monitored regularly to maintain a consistent appearance.
Mixed product will contain 876-9081, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of these materials. Please note that the catalyzed mixtures have short pot lives and therefore mix only a quantity that can be used within two to three hours. Clean equipment immediately after use.
Total recommended film thickness of 283-322 P.U. Primer White plus topcoat is not to exceed 6 mils dry.Topcoats use with 283-322: Lustrate 109-XXX and 634-XXX
- PDF Name: CA-PIS_283-322_Urethane_White_PU_Pigmented_Primer
- Sec au toucher: 20 - 30 minutes
- Files: CA-PIS_283-322_Urethane_White_PU_Pigmented_Primer.pdf
- Sec au ponçage: 3 - 4 hours
- Sec à l'empilage: Overnight
- Sec au toucher: Flash off before entering oven
- Sec au ponçage: 3 hours
- COV moins exemption g/L: 568
- COV g/L: 568
- Sec à l'empilage: 4 hours
- Remarque:
See individual compliance sheets for specific data
- spec_description:
Polyurethane Primer is a fast-curing, high solid white primer for application on wood or wood products. It is a two-component polyurethane system providing excellent filling properties, good flexibility and excellent sanding properties.
- spec_uses:
283-322 is suitable for priming all types of MDF and wood substrates for interior use. It can be used to give closed grain finishes.
- Utilisations suggérées:
Spray
- Catalyseur:
3:1 (33%) with 876-9081 (other hardeners possible)
- Vie en pot:
2-3 hours
- Viscosité d'application:
Zahn #2 signature cup 20-25 seconds
- Diluant: 121-834 or 800-5301
- Retardateur: 800-5328 EEP (not normally required)
- Solvant de nettoyage: Lacquer Thinner (do not mix with product)
- Épaisseur du film à l'application recommandée: 4-6 wet mils
- Pouvoir couvrant:
N/A
- Remarque:
N/A
- Viscosité:
Zahn #4 signature cup 35 sec at 25°C
- Point d'éclair: 21°C (70°F)
- Densité (kg/L): 1.22
- Solides (% en poids): 53%
- Solides (% en volume): 35%
- Stabilité à l'entreposage (mois): 12
- Isolante
- 401-0330 Isolante PU Clear Sealer
- Codes de produit:
410-0330
- Surface Preparation:
Wood must be sanded with a 120, 150 or 180 grit paper and free of dust and all contaminants. Plastic substrates should be scuffed with Scotch Brite to improve adhesion. Substrates that cannot be sanded should be wiped clean and degreased if possible.
- General Information:
Mix product with hardener and reducer to the recommended viscosity. Apply 2 to 4 wet mils on a sanded surface. Let dry for 30 to 60 minutes and apply the desired topcoat. If the drying time exceeds 4 hours, sanding is required to keep a good adhesion. Once catalyzed with 999-0660, this product will contain isocyanates. Take necessary precautions for the handling and use of this product. See MSDS. Total dry film build of Isolante should not exceed 1 dry mil. The total system build will be dependent upon the topcoat applied.
For a complete system cure, the system must be applied at a temperature above 18ºC and relative humidity below 65%.
Complete system must be verified and approved by AkzoNobel before going on production.
Suitable topcoats include Lustrate, Chemlite, Reslack and Plasticolor. Others may be recommended as well, speak with your technical sales representative.
- PDF Name: CA-PIS_401-0330_Isolante_PU_Clear_Sealer
- Sec au toucher: 30 - 60 minutes
- Files: CA-PIS_401-0330_Isolante_PU_Clear_Sealer.pdf
- Sec au ponçage: 4 hours
- Sec à l'empilage: 8 hours
- Sec au toucher: 5 - 10 minutes
- Sec au ponçage: 20 - 30 minutes
- COV moins exemption g/L: 651
- COV g/L: 651
- Sec à l'empilage: 4 hours
- Remarque:
See individual compliance sheets for specific data
- spec_description:
Isolante Sealer is a two component ‘tie-coat’ polyurethane type sealer that is designed to improve the adhesion between topcoats and substrates where poor adhesion would otherwise be obtained. These would include a wide variety of plastics, stained or exotic woods.
- spec_uses:
Isolante Sealer is normally used as a washcoat applied directly to the substrate in order to ensure good adhesion and oil blocking properties. It is suitable for all types of wood, MDF, veneers and some type of plastic.
- Utilisations suggérées:
Spray
- Catalyseur:
2:1 with 999-0660
- Vie en pot: 2-3 hours
- Viscosité d'application:
20-25 sec Zahn #2 at 25°C
- Diluant: 800-5301 or 121-834
- Retardateur: 800-5328 EEP
- Solvant de nettoyage: Lacquer Thinner (do not mix with product)
- Épaisseur du film à l'application recommandée: 2-4 mils wet
- Pouvoir couvrant:
N/A
- Remarque:
N/A
- Viscosité:
Zahn #4 signature cup 24 sec at 25°C
- Point d'éclair: -6°C
- Densité (kg/L): 0.94 ± 2% at 25°C
- Solides (% en poids): 31 ± 2%
- Solides (% en volume): 21 ± 2%
- Stabilité à l'entreposage (mois): 12
- Lustrate
- 436-1399 Lustrate PU Clear Topcoat
- Codes de produit:
436-1399 High Gloss
- Surface Preparation:
Primer should be well sanded using 240, 320 and 360 grit stearated paper. Care should be taken during sanding to avoid sanding through the primer. The clear system sealer is 436-2104.
- General Information:
Mix the desired amount of material and apply 4-6 mils wet. The coating when cured is very suitable to be buffed and polished where dust free conditions are not available.
The relative humidity in the application and drying rooms should never exceed 75%. Viscosity on the mixed material should be monitored regularly to maintain a consistent appearance.
The mixed product contains 876-9081, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of these materials.
Total recommended film thickness of Lustrate is not to exceed 6 mils dry.Sealers to use under 436-1399: polyurethane 436-2104 or 283-3XX or polyester (740-XXX).
- PDF Name: CA-PIS_436-1399_Lustrate_PU_Clear_Topcoat
- Sec au toucher: 15 - 30 minutes
- Files: CA-PIS_436-1399_Lustrate_PU_Clear_Topcoat.pdf
- Sec au ponçage: Overnight
- Sec à l'empilage: Overnight
- Sec au toucher: Flash off before entering oven
- Sec au ponçage: 3 hours
- COV moins exemption g/L: 450
- COV g/L: 450
- Sec à l'empilage: 4 hours
- Remarque:
See individual compliance sheets for specific data
- spec_description:
Lustrate is a two component polyurethane enamel with a tough cross linked film. The coating is very resistant to scratching and household chemicals when cured, and can provide exceptional gloss and clarity.
- spec_uses:
Lustrate is used whenever premium performance characteristics are required for interior wood finishing.
- Utilisations suggérées: Spray
- Catalyseur:
1:1 with 876-9081
- Vie en pot:
3 hours
- Viscosité d'application:
Zahn #2 signature cup 20-25 seconds
- Diluant: 121-834 or 800-5301
- Retardateur: 800-5328 EEP
- Solvant de nettoyage: Lacquer Thinner (do not mix with product)
- Épaisseur du film à l'application recommandée: 4-6 wet mils
- Pouvoir couvrant:
N/A
- Remarque:
N/A
- Viscosité:
Zahn #2 signature cup 45 sec at 25°C
- Point d'éclair: 24°C (75°F)
- Densité (kg/L): 1.03
- Solides (% en poids): 56%
- Solides (% en volume): 50%
- Stabilité à l'entreposage (mois): 12
- Chemlite
- 436-31XX Chemlite PU Clear Topcoat
- Codes de produit:
436-3108 10° Matte
436-3125 25° Low Gloss
436-3141 40° Satin
436-3191 90° High Gloss - Surface Preparation:
Topcoats should be well sanded using 240, 280 or 320 grit stearated paper.
- General Information:
Mix the desired amount of material and apply 4-5 mils wet. Do not use excess reducer (>10%), this product is relatively low solids and will appear ‘hungry’ if too much thinner is added.
The relative humidity in the application and drying rooms should never exceed 75%. Viscosity on the catalyzed material should be monitored regularly to maintain a consistent appearance.
Mixed product will contain 999-067, an isocyanate based co reactant. Please follow all precautions associated with handling and use of these materials.
Total recommended film thickness of Chemlite is not to exceed 6 mils dry.The sealer for this product is 436-2104.
- PDF Name: CA-PIS_436-31XX_Chemlite_PU_Clear_Topcoat
- Sec au toucher: 20 - 30 minutes
- Files: CA-PIS_436-31XX_Chemlite_PU_Clear_Topcoat.pdf
- Sec au ponçage: Overnight
- Sec à l'empilage: Overnight
- Sec au toucher: Flash off before entering oven
- Sec au ponçage: 3 hours
- COV moins exemption g/L: 715
- COV g/L: 715
- Sec à l'empilage: 8 hours
- Remarque:
See individual compliance sheets for specific data
- spec_description:
Chemlite is a two component polyurethane finish for interior use. The Chemlite system provides exceptional resistance to discolouration and gives a crosslinked finish that is tough and durable. The coating contains UV absorbers to minimize discolouration of light sensitive substrates.
- spec_uses:
Chemlite is an excellent choice for finishing fine furniture, cabinetry and all other wood surfaces intended for interior use. Chemlite is also “water-white” meaning it is exceptional over pigmented basecoats where colour is important.
- Utilisations suggérées: Spray
- Catalyseur:
10 parts Chemlite, 2 parts 999-067 (20% b.v.)
- Vie en pot:
3 hours
- Viscosité d'application:
Zahn #2 signature cup 20-25 seconds
- Diluant: 121-834 or 800-5301
- Retardateur: 800-5328 EEP
- Solvant de nettoyage: Lacquer Thinner (do not mix with product)
- Épaisseur du film à l'application recommandée: 4-5 wet mils
- Pouvoir couvrant:
N/A
- Remarque:
N/A
- Viscosité:
Zahn #2 signature cup 26 sec at 25°C
- Point d'éclair: 24°C (75°F)
- Densité (kg/L): 0.95
- Solides (% en poids): 25%
- Solides (% en volume): 19%
- Stabilité à l'entreposage (mois): 12
- Lustrate
- 436-2104 Lustrate PU Clear Sealer
- Codes de produit:
436-2104
- Surface Preparation:
Substrate should be sanded with 120, 150 or 180 grit sandpaper prior to finishing. Difficult or oily substrates may require the use of 401-033 Isolante Sealer prior to priming to ensure maximum adhesion.
- General Information:
Prepare material as per hardener mixing ratio and apply over desired surface at 3-5 mils wet.
Mixed product will contain 999-067, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of these materials. The relative humidity in the application and drying rooms should never exceed 75%.
After drying, scuff sand with 280-320 grit paper and topcoat within eight hours. If left over eight hours, the sealer should be re-sanded prior to topcoating.
Total dry film build of the system including topcoat is not to exceed 6 dry mils.Topcoats to use over 436-2104: Chemlite 436-31XX or Lustrate 436-1399.
- PDF Name: CA-PIS_436-2104_Lustrate_PU_Clear_Sealer
- Sec au toucher: 10 - 15 minutes
- Files: CA-PIS_436-2104_Lustrate_PU_Clear_Sealer.pdf
- Sec au ponçage: 20 - 30 minutes
- Sec à l'empilage: Overnight
- Sec au toucher: 3 - 5 minutes
- Sec au ponçage: 10 - 15 minutes
- COV moins exemption g/L: 692
- COV g/L: 692
- Sec à l'empilage: 2 - 4 hours
- Remarque:
See individual compliance sheets for specific data
- spec_description:
Lustrate Sealer is designed to provide the improved adhesion characteristics typical of a urethane material. When topcoated with Chemlite or Lustrate, the system provides exceptional durability and light stability.
- spec_uses:
436-2104 is suitable for sealing all types of wood and wood veneers for interior use. The product provides very good water resistance and offers protection from tannin bleed.
- Utilisations suggérées: Spray
- Catalyseur:
10:1 (10%) with 999-067 (other hardeners possible)
- Vie en pot:
2-3 hours
- Viscosité d'application:
Zahn #2 signature cup 20-25 seconds
- Diluant: 100-120, 800-5301 or 121-834
- Retardateur: 800-5328 EEP
- Solvant de nettoyage: Lacquer Thinner (do not mix with product)
- Épaisseur du film à l'application recommandée: 3-5 wet mils
- Pouvoir couvrant:
N/A
- Remarque:
N/A
- Viscosité:
Zahn #2 signature cup 20 sec at 25°C
- Point d'éclair: -1°C (30°F)
- Densité (kg/L): 0.94
- Solides (% en poids): 27%
- Solides (% en volume): 21%
- Stabilité à l'entreposage (mois): 12
Besoin d’aide ? Contactez notre équipe d’experts en revêtement du bois.
