Chemlife

117-24XX Chemlife® 24 White Conversion Varnish Pigmented Topcoat

Codes de produit:

117-2410 10° Matte
117-2420 20° Low Gloss
117-2435 35° Satin
117-2450 50° Semi-Gloss
117-2490 90° High Gloss

Surface Preparation:

Primer should be sanded using 240 and 320 grit stearated paper. The primer should be topcoated within eight hours of sanding. Care should be taken during sanding through the primer.

General Information:

Catalyze and reduce the material as recommended. Chemlife 24 White is applied in one or two coats and can be used on all kinds of wood meant for interior use. A thorough sanding between the coats is essential to the adhesion. The second and subsequent coats must be applied the same day as the previous coat is sanded. Chemlife 24 White cannot be used on metal, old oil or cellulose lacquers. Total recommended film build of the system should not exceed 6 mils dry. Over the primer, the topcoat should not exceed 4 mils dry.

To ensure proper sheen, the catalyzed material should be agitated at all times. Chemlife 24 White must be thoroughly stirred while adding catalyst and thinner in the recommended mixing ratio. Contact with metal surfaces should be avoided once the Chemlife 24 White has been catalyzed.

Chemlife 24 White must not be polluted with oil, varnish or the like and must not be sanded with steel wool between coats. To obtain complete cure, Chemlife 24 White must be applied at a temperature above 18ºC and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapours. Finished surface must not be cleaned with ammonia containing products.

Primers to use with 117-24XX: Chemlife White primer 522-2400, 220-2250 and 522-1410.

PDF Name: CA-PIS_117-24XX_Chemlife_24_White_Conversion_Varnish_Pigmented_Topcoat

Sec au toucher: 15 – 20 minutes

Files: CA-PIS_117-24XX_Chemlife_24_White_Conversion_Varnish_Pigmented_Topcoat.pdf

Sec au ponçage: 3 hours

Sec à l'empilage: 16 hours

Sec au toucher: Flash off before entering oven

Sec au ponçage: 1 hour

COV moins exemption g/L: 449

COV g/L: 449

Sec à l'empilage: 3 hours

Remarque: N/A

Remarque:

See individual compliance sheets for specific data

spec_description:

Chemlife 24 White is an acid curing, light stable, fast drying Reactive Amino Coating (RAC) with good building properties. It gives a smooth, knock-proof and hardwearing surface resisting influence from alcohol, water, etc. Due to its 24 hours pot-life, Chemlife 24 White provides the customer with minimum waste resulting in lower production costs. It also provides very good light stability based on the type of resin used and superior vertical hang.

Special recognition: when applied as specified, will meet required performance for the ANSI/KCMA A161.1 1990 9.0 Finish Test. Recommended: Architectural Woodwork Institute (AWI) O.P.4

spec_uses:

This product is used as the final coat over wood, plywood, chipboard, etc., meant for interior use. This product is recommended for kitchen cabinets, high build office or residential furniture as well as many other interior wood applications where high build and durability are required.

Utilisations suggérées:

Wood Finish/Spray

Catalyseur:

10% 873-1251

Vie en pot:

24 hours

Viscosité d'application:

22-25 sec Zahn #2 at 25°C

Diluant: 121-803 or 121-8020 if necessary

Retardateur: 800-5328 EEP (2-3% maximum)

Solvant de nettoyage: Lacquer thinner

Épaisseur du film à l'application recommandée: 3 to 5 wet mils

Pouvoir couvrant:

17-18 m²/l (190 pi²/l) at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.

Remarque:

N/A

Viscosité:

Zahn #3 signature cup 20 sec at 25°C

Point d'éclair: 12°C (55°F)

Densité (kg/L): 1.13 ± 2% at 25°C

Solides (% en poids): 60 ± 2%

Solides (% en volume): 45 ± 2%

Stabilité à l'entreposage (mois): 12

Chemlife

117-24XX Chemlife® 24 White Conversion Varnish Pigmented Topcoat

Find distributor Trouver un distributeur

spec_description:

Special recognition: when applied as specified, will meet required performance for the ANSI/KCMA A161.1 1990 9.0 Finish Test. Recommended: Architectural Woodwork Institute (AWI) O.P.4

BACK

Chemlife

117-24XX Chemlife® 24 White Conversion Varnish Pigmented Topcoat

spec_description:

Special recognition: when applied as specified, will meet required performance for the ANSI/KCMA A161.1 1990 9.0 Finish Test. Recommended: Architectural Woodwork Institute (AWI) O.P.4

Product codeCodes de produit
Codes de produit:

117-2410 10° Matte
117-2420 20° Low Gloss
117-2435 35° Satin
117-2450 50° Semi-Gloss
117-2490 90° High Gloss

Informations sur le produit

Product specificationsSpécifications du produit

Viscosité:

Zahn #3 signature cup 20 sec at 25°C

Point d'éclair: 12°C (55°F)

Densité (kg/L): 1.13 ± 2% at 25°C

Solides (% en poids): 60 ± 2%

Solides (% en volume): 45 ± 2%

Stabilité à l'entreposage (mois): 12

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Télécharger les fiches d'information sur les produits

Files: CA-PIS_117-24XX_Chemlife_24_White_Conversion_Varnish_Pigmented_Topcoat.pdf

Ces produits sont uniquement conçus pour un usage industriel. AkzoNobel considère la sécurité comme une priorité absolue. Veuillez vous reporter à la fiche de données de sécurité pour plus d'informations sur l'utilisation sécuritaire de ce produit.

L'épaisseur du feuil, la porosité du substrat, le mouvement de l'air, la chaleur et l'humidité ont une forte incidence sur les temps de séchage. Les températures sont basées sur la température réelle du panneau de bois. Le temps de séchage peut varier en fonction du temps nécessaire pour que les panneaux de bois atteignent ces températures. La température de durcissement minimale de 18 °C/64 °F doit être maintenue pendant tout le cycle de durcissement afin d'obtenir l'intégrité de revêtement indiquée dans les caractéristiques du produit.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

À propos de notre marque	Produits	Distributeurs	Utilisation
Nous contacter	Produits Pré-Catalysés	Nos distributeurs	Tutoriels vidéo
	Produits Post-Catalysés	Portail de commande de revêtements pour bois	Guide de résolution des problèmes
	Systèmes en polyuréthane		Glossaire
	Systèmes de couleur		Spécifications techniques
	Produits vinylique		Application mobile
	Nitrocellulose
	Spécialisés

Témoins	Paramètres des témoins	Confidentialité	Plan du site