Optiset
131-82XX Optiset® 550 Pre-Cat White Topcoat
Codes de produit:

131-8215 15° Low Gloss

131-8225 25° Low Gloss
131-8240 40° Satin
131-8260 60° Semi-Gloss
Surface Preparation:

Wood substrate should be sanded with 120, 150 or 180 grit paper prior to coating. Primers should be sanded with 280/320 grit stearated paper prior to topcoating. When recoating, the previous coat of Optiset 550 or primer must be sanded and the next coat applied within eight hours. Optiset 550 White cannot be used on metal, old oil or cellulose lacquers.
General Information:

Agitate material before use. Always mix Optiset 550 while adding hardener and reducers in the recommended mixing ratios. Optiset 550 must be agitated thoroughly at all times to ensure product consistency and consistent gloss.

Apply at 3-5 mils wet on sanded or primed substrate. Further coats may be applied after complete drying followed by sanding with 280/320 grit stearated paper. Maximum film build of Optiset 550 White should not exceed 4 mils dry. Maximum film build of total coating system must not exceed 4 mils dry. The second and subsequent coats must be applied the same day as the previous coat is sanded.

Contact with metal surfaces should be avoided.

Optiset 550 White must not be polluted with oil, varnish or the like and must not be sanded with steel wool between the coats. Optiset 550 White must not be used and dried at temperatures below 18°C or relative humidity above 65%. During hardening the enamel must not be exposed to ammonia vapors. Ammonia cleaners should not be used for cleaning the finished surface. This may accelerate discoloration.

Basecoats to use with 131-82XX: 522-1624, 545-8016, 546-7257 or self-seal
PDF Name: CA-PIS_131-82XX_Optiset_550_Pre-Cat_White_Topcoat
Sec au toucher: 10 – 15 minutes
Files: CA-PIS_131-82XX_Optiset_550_Pre-Cat_White_Topcoat.pdf
Sec au ponçage: 2 hours
Sec à l'empilage: 3 hours
Sec au toucher: Flash off before entering oven
Sec au ponçage: 30 - 45 minutes
COV moins exemption g/L: <550
COV g/L: <451
Sec à l'empilage: 60 - 90 minutes
Remarque: N/A
Remarque:

See individual compliance sheets for specific data
spec_description:

Optiset 550 is a one-component, pigmented Pre-Catalyzed Reactive Amino Coating (RAC) with good resistance properties. This product meets the German “E-1” classification for the emission of formaldehyde as tested by an accredited laboratory using North American test methods. This is a fast building pigmented pre-catalyzed RAC due to its high solid content (32% volume). Optiset 550 demonstrates very good moisture, household wear, household chemical and mar resistance. The coating has light stable properties due to the type of resin used. This coating may be catalyzed to further enhance its durability. Contact your coating supplier for a recommendation. Optiset 550 has very low odor during the curing process while maintaining its rapid dry and cure properties.

Special Recognition: Meets Kitchen Cabinet Manufacturer Association (KCMA) Standards. Recommended: Architectural Woodwork Institute (AWI). O.P.2.
spec_uses:

Optiset 550 is recommended for kitchen cabinets, office and household furniture, as well as other interior wood applications.
Utilisations suggérées: Spray
Catalyseur:

100 parts 131-82XX to 3 parts 999-017*
Vie en pot: 8 hours*
Viscosité d'application:

Zahn #2 signature cup 35 – 36 seconds
Diluant: 121-803 or 121-8020
Retardateur: 800-5328 EEP
Solvant de nettoyage: Lacquer Thinner
Épaisseur du film à l'application recommandée: 3 – 5 mils wet
Pouvoir couvrant:

12 m2/l (130 pi2/l) at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.
Remarque:

*Amount of catalyst required & pot life if material is catalyzed.
Viscosité:

Zahn #2 signature cup 36 sec at 77°F (25°C)
Point d'éclair: -20°C (-4°F)
Densité (kg/L): 1.06
Solides (% en poids): 47%
Solides (% en volume): 31%
Stabilité à l'entreposage (mois): 6

Optiset

131-82XX Optiset® 550 Pre-Cat White Topcoat

Find distributor Trouver un distributeur

spec_description:

Optiset 550 is a one-component, pigmented Pre-Catalyzed Reactive Amino Coating (RAC) with good resistance properties. This product meets the German “E-1” classification for the emission of formaldehyde as tested by an accredited laboratory using North American test methods. This is a fast building pigmented pre-catalyzed RAC due to its high solid content (32% volume). Optiset 550 demonstrates very good moisture, household wear, household chemical and mar resistance. The coating has light stable properties due to the type of resin used. This coating may be catalyzed to further enhance its durability. Contact your coating supplier for a recommendation. Optiset 550 has very low odor during the curing process while maintaining its rapid dry and cure properties.

Special Recognition: Meets Kitchen Cabinet Manufacturer Association (KCMA) Standards. Recommended: Architectural Woodwork Institute (AWI). O.P.2.
Read more
  2. Accueil
  3. MAP Products
  4. Produits
  5. Produits pré-catalysés
  6. 131-82XX Optiset® 550 Pre-Cat White Topcoat
BACK

    Optiset

    131-82XX Optiset® 550 Pre-Cat White Topcoat

    spec_description:

    Optiset 550 is a one-component, pigmented Pre-Catalyzed Reactive Amino Coating (RAC) with good resistance properties. This product meets the German “E-1” classification for the emission of formaldehyde as tested by an accredited laboratory using North American test methods. This is a fast building pigmented pre-catalyzed RAC due to its high solid content (32% volume). Optiset 550 demonstrates very good moisture, household wear, household chemical and mar resistance. The coating has light stable properties due to the type of resin used. This coating may be catalyzed to further enhance its durability. Contact your coating supplier for a recommendation. Optiset 550 has very low odor during the curing process while maintaining its rapid dry and cure properties.

    Special Recognition: Meets Kitchen Cabinet Manufacturer Association (KCMA) Standards. Recommended: Architectural Woodwork Institute (AWI). O.P.2.
    Read more
    Product codeCodes de produit
    Codes de produit:

    131-8215 15° Low Gloss

    131-8225 25° Low Gloss
    131-8240 40° Satin
    131-8260 60° Semi-Gloss

    Informations sur le produit

    Product specificationsSpécifications du produit

    Viscosité:

    Zahn #2 signature cup 36 sec at 77°F (25°C)
    Point d'éclair: -20°C (-4°F)
    Densité (kg/L): 1.06
    Solides (% en poids): 47%
    Solides (% en volume): 31%
    Stabilité à l'entreposage (mois): 6

    Find distributor Trouver un distributeur

    Télécharger les fiches d'information sur les produits

    Files: CA-PIS_131-82XX_Optiset_550_Pre-Cat_White_Topcoat.pdf

    Ces produits sont uniquement conçus pour un usage industriel. AkzoNobel considère la sécurité comme une priorité absolue. Veuillez vous reporter à la fiche de données de sécurité pour plus d'informations sur l'utilisation sécuritaire de ce produit.

    L'épaisseur du feuil, la porosité du substrat, le mouvement de l'air, la chaleur et l'humidité ont une forte incidence sur les temps de séchage. Les températures sont basées sur la température réelle du panneau de bois. Le temps de séchage peut varier en fonction du temps nécessaire pour que les panneaux de bois atteignent ces températures. La température de durcissement minimale de 18 °C/64 °F doit être maintenue pendant tout le cycle de durcissement afin d'obtenir l'intégrité de revêtement indiquée dans les caractéristiques du produit.

    Image

    Recommended for interior woodwork

    OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

    View our ranges

    Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

    Chemcraft Products
    Chemcraft Products
    Chemcraft Products
    Chemcraft Products
    Chemcraft Products
    Chemcraft Products
    Chemcraft Products
    Chemcraft Products
    Chemcraft Products
    Chemcraft Products
    Chemcraft Products
    Chemcraft Products
    Chemcraft Products
    Chemcraft Products
    Chemcraft Products
    Chemcraft Products

    View our ranges

    Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

    Besoin d’aide ? Contactez notre équipe d’experts en revêtement du bois.

    Contactez notre équipe

    À propos de notre marque Produits Distributeurs Utilisation
    Nous contacter Produits Pré-Catalysés Nos distributeurs Tutoriels vidéo
      Produits Post-Catalysés Portail de commande de revêtements pour bois Guide de résolution des problèmes
      Systèmes en polyuréthane   Glossaire
      Systèmes de couleur   Spécifications techniques
      Produits vinylique   Application mobile
      Nitrocellulose    
      Spécialisés    
           
    Témoins Paramètres des témoins Confidentialité Plan du site

    À propos de notre marque

    Nous contacter

    Produits

    Produits Pré-Catalysés

    Produits Post-Catalysés

    Systèmes en polyuréthane

    Systèmes de couleur

    Produits vinylique

    Nitrocellulose

    Spécialisés

    Distributeurs

    Nos distributeurs

    Portail de commande de revêtements pour bois

    Utilisation

    Tutoriels vidéo

    Guide de résolution des problèmes

    Glossaire

    Spécifications techniques

    Application mobile

    Plan du site