GLAZE

825-3678 Promatch® ProGlaze Neutral Dry Glaze

Product Codes:

825-3678

Surface Preparation:

N/A

General Information:

Prior to use, agitate thoroughly and tint as required with 844 line tints to a maximum of 7% by volume. Apply the Promatch Dry Glaze Neutral over a sealer coat. Sand sealer with 280/320 grit paper before use. The Promatch Dry Glaze Neutral needs to be applied and topcoated within 8 hours of sanding the sealer.

Apply by spray and allow the Promatch Dry Glaze Neutral II to dry before removing excess material with a solvent-wetted rag or Scotch-Brite pad. To ensure good adhesion of the finished system, remove as much of the Promatch Dry Glaze Neutral as possible from the exposed areas before topcoating.

Promatch ProGlaze Neutral Dry Glaze must be thoroughly agitated to ensure product consistency.

PDF Name: US-PIS_825-3678_Promatch_ProGlaze_Neutral_Dry_Glaze

Tack Free Time: N/A

Files: US-PIS_825-3678_Promatch_ProGlaze_Neutral_Dry_Glaze.pdf

Dry to Sand : N/A

Dry to Stack: N/A

Tack Free Time: N/A

Dry to Sand: N/A

Dry to Stack: N/A

Note: N/A

spec_description:

Promatch ProGlaze Neutral Dry Glaze is an all-purpose dry glaze for furniture and cabinets. It is specially formulated to be used with 844 tints and can be tinted up to a maximum of 7% by volume.

spec_uses:

Promatch ProGlaze Neutral Dry Glaze is used to provide a highlighting effect on furniture, cabinets and millwork. When properly applied, it will provide a highlighted effect with excellent adhesion properties.

VOC less exempt lb/gal: 0.0

VOC lb/gal: 0.0

VOC less exempt g/l: 0.0

VOC g/l: 0.0

VOC lb/lb Solid: 0.0

VHAPs lb/lb Solid: 0.0

Note:

The addition of 844 tints will cause an increase in VOC. Therefore a maximum of 6% by volume is required to maintain low VOC requirements (<240 g/l).

Suggested Uses:

Wood Glaze

Mixing Ratio:

N/A

Pot Life: N/A

Application Viscosity:

N/A

Reducer: N/A

Retarder: N/A

Clean-up Solvent: 800-5500

Recommended Wet Film: N/A

Coverage:

N/A

Note application:

N/A

Viscosity:

N/A

Flash Point: 109°F (43°C)

Density (lb/gal): 11.31

Solid (% by weight): 9.7%

Solid (% by volume): 8.43%

Shelf Life (months): 24

GLAZE

825-3678 Promatch® ProGlaze Neutral Dry Glaze

Find distributor

spec_description:

Promatch ProGlaze Neutral Dry Glaze is an all-purpose dry glaze for furniture and cabinets. It is specially formulated to be used with 844 tints and can be tinted up to a maximum of 7% by volume.

Back

GLAZE

825-3678 Promatch® ProGlaze Neutral Dry Glaze

spec_description:

Promatch ProGlaze Neutral Dry Glaze is an all-purpose dry glaze for furniture and cabinets. It is specially formulated to be used with 844 tints and can be tinted up to a maximum of 7% by volume.

Product code
Product Codes:

825-3678

Product information

Product specifications

Viscosity:

N/A

Flash Point: 109°F (43°C)

Density (lb/gal): 11.31

Solid (% by weight): 9.7%

Solid (% by volume): 8.43%

Shelf Life (months): 24

Uses

Environmental data (as supplied)

Application data

Surface Preparation

General Information

Drying Times

Find distributor

Download product information sheets

Files: US-PIS_825-3678_Promatch_ProGlaze_Neutral_Dry_Glaze.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap