GLAZE

825-37XX Promatch® Glaze SB Stain

Product Codes:

825-3700 Neutral
825-3701 Burnt Umber
825-3702 Van Dyke
825-3703 Black
825-3704 Raw Sienna
825-3705 Medium Brown
825-3706 Burnt Sienna
825-3707 White
825-3708 Chocolate

Surface Preparation:

N/A

General Information:

Prior to use, mix Promatch Glaze carefully and reduce viscosity by adding approximately 50 – 100% reducer. Apply the reduced Glaze by spraying or with a rag. Allow two to three minutes air drying before wiping. Wipe clean and do not leave on any excess material that may interfere with optimum adhesion.

Promatch Glaze must be thoroughly agitated to ensure product consistency.

Product must be thoroughly agitated before use.

After wiping, brush blending, highlighting and complete drying, it can be overcoated by a suitable system such as ECat 431-11XX, Varicure® 431-46XX, ES Lacquer Elite II 431-47XX, Chemguard II 431-70XX, Opticlear 431-80XX, Plastofix Light 421-48XX, Chemlife® 24 421-63XX, EVar 421-80XX, Danspeed Elite 424-44XX and Danspeed II 424-45XX as well as the sealers associated with these systems.

PDF Name: US-PIS_825-37XX_Promatch_Glaze_SB_Stain

Tack Free Time: N/A

Files: US-PIS_825-37XX_Promatch_Glaze_SB_Stain.pdf

Dry to Sand : N/A

Dry to Stack: N/A

Tack Free Time: N/A

Dry to Sand: N/A

Dry to Stack: N/A

Note: N/A

spec_description:

Promatch Glaze 825-37XX is an all-purpose glaze for furniture and cabinets. It should be stirred well due to the heavy concentration of certain additives and tints. Application may be by hand or spray. Promatch Glaze is reducible.

spec_uses:

Promatch Glaze is used for coloring of wood and is especially developed for furniture coating systems. When properly applied, it will enhance the natural beauty of the wood. Promatch Glaze is used for indoor use and is normally applied over a washcoat.

VOC less exempt: 5.50 – 6.00

VOC lb/gal: 5.00 – 6.00

VOC less exempt g/l: 665 - 720

VOC g/l: 665 - 720

VOC lb/lb Solid: 1.75 – 2.26

VHAPs lb/lb Solid: 0.20 – 0.30

Note:

N/A

Suggested Uses:

Wood Stain

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

N/A

Reducer: 800-4310

Retarder: N/A

Clean-up Solvent: 800-4310

Recommended Wet Film: N/A

Coverage:

N/A

Note application:

N/A

Viscosity:

~2000 CPS at 77°F

Flash Point: 53°F (12°C)

Density (lb/gal): 8.6 – 9.0

Solid (% by weight): 21 – 36%

Solid (% by volume): 19 - 24%

Shelf Life (months): 24

GLAZE

825-37XX Promatch® Glaze SB Stain

Find distributor Trouver un distributeur

spec_description:

BACK

GLAZE

825-37XX Promatch® Glaze SB Stain

spec_description:

Product codeCodes de produit
Product Codes:

825-3700 Neutral
825-3701 Burnt Umber
825-3702 Van Dyke
825-3703 Black
825-3704 Raw Sienna
825-3705 Medium Brown
825-3706 Burnt Sienna
825-3707 White
825-3708 Chocolate

Product information

Product specificationsSpécifications du produit

Viscosity:

~2000 CPS at 77°F

Flash Point: 53°F (12°C)

Density (lb/gal): 8.6 – 9.0

Solid (% by weight): 21 – 36%

Solid (% by volume): 19 - 24%

Shelf Life (months): 24

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_825-37XX_Promatch_Glaze_SB_Stain.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap