VIVID COLOR SPRAY Stain Base

890-1600 Promatch® Vivid Color Spray SB Stain

Product Codes:

890-1600

Surface Preparation:

Wood substrate must be sanded using 120, 150 or 180 grit paper prior to staining. On wood such as maple, coarser sanding, such as 150 grit, should be performed to avoid polishing of the wood surface. Hand sanding in the direction of the grain following orbital sanding will remove swirl marks.

General Information:

Product must be thoroughly agitated before use and during application for color consistency.

Product can be tinted with 844 Tints up to 10%.

Dirty and clean rags must be disposed of in a safe and approved manner. The use of closed containers filled with water is the most appropriate way for disposal of the rags.

Drying time is very short and 20 minutes is sufficient prior to apply sealer. However, heavy coats in dark colors should get at least 30 minutes drying. The suggested drying time must be adhered to in order to ensure proper adhesion.

PDF Name: US-PIS_890-1600_Promatch_Vivid_Color_Spray_SB_Stain

Tack Free Time: N/A

Files: US-PIS_890-1600_Promatch_Vivid_Color_Spray_SB_Stain.pdf

Dry to Sand : N/A

Dry to Stack: N/A

Tack Free Time: N/A

Dry to Sand: N/A

Dry to Stack: N/A

Note: N/A

spec_description:

890-1600 is a spray stain base formulated especially to be tinted with the Huls 844 colorants. Its unique solvent blend also gives the option of using permatone dyes or concentrated liquid dyes for the development of rich and deep colors.

spec_uses:

890-1600 is a spray stain base that gives you the opportunity to develop a variety of colors for interior wood application.

VOC less exempt: <6.75

VOC lb/gal: <5.00

VOC less exempt g/l: <810

VOC g/l: <600

VOC lb/lb Solid: <30

VHAPs lb/lb Solid: <0.00

Note:

N/A

Suggested Uses:

Wood Stain

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

N/A

Reducer: No reduction required

Retarder: N/A

Clean-up Solvent: 800-5500 Acetone or lacquer thinner

Recommended Wet Film: N/A

Coverage:

N/A

Note application:

N/A

Viscosity:

N/A

Flash Point: -4 ˚F (-20°C)

Density (lb/gal): 6.84

Solid (% by weight): 2.6%

Solid (% by volume): 2.1%

Shelf Life (months): 24

VIVID COLOR SPRAY Stain Base

890-1600 Promatch® Vivid Color Spray SB Stain

Find distributor Trouver un distributeur

spec_description:

BACK

VIVID COLOR SPRAY Stain Base

890-1600 Promatch® Vivid Color Spray SB Stain

spec_description:

Product codeCodes de produit
Product Codes:

890-1600

Product information

Product specificationsSpécifications du produit

Viscosity:

N/A

Flash Point: -4 ˚F (-20°C)

Density (lb/gal): 6.84

Solid (% by weight): 2.6%

Solid (% by volume): 2.1%

Shelf Life (months): 24

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_890-1600_Promatch_Vivid_Color_Spray_SB_Stain.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap