CHEMBASE Pigmented Primer

545-5104 Chembase White NC Pigmented Primer

Product Codes:

545-5104

Surface Preparation:

Substrate should be sanded using 120, 150 or 180 grit stearated paper prior to coating. Primers should be sanded with 280/320 grit stearated paper prior to being coated.

General Information:

Chembase White may be applied in two or more coats, depending on the desired finish. The dry film build should not exceed 2 – 3 mils. The total dry film build of the system should not exceed 4 mils.

Chembase White should be thoroughly stirred, and mixed with an appropriate amount of reducer.

Chembase White must not be polluted with oil, varnish or the like and must not be sanded with steel wool between coats.

Chembase White must not be used and dried at temperatures below 64°F or relative humidity above 65%. During the curing process, the coating must not be exposed to ammonia vapors. Ammonia cleaners should not be used for cleaning the finish surfaces. This may accelerate discoloration.

PDF Name: US-PIS_545-5104_Chembase_White_NC_Pigmented_Primer

Tack Free Time: 10 – 15 minutes

Files: US-PIS_545-5104_Chembase_White_NC_Pigmented_Primer.pdf

Dry to Sand : 45 minutes

Dry to Stack: 2 hours

Tack Free Time: Flash off before entering oven

Dry to Sand: 20 – 30 minutes

Dry to Stack: 45 minutes

Note: N/A

spec_description:

Chembase White is a ready to use, white nitrocellulose primer. It is a single pack, conventional lacquer basecoat recommended as the primer for Chemlack White 230-65XX. Chembase White dries to sand quickly and powders well during sanding.

spec_uses:

N/A

VOC less exempt: <5.00

VOC lb/gal: <3.30

VOC less exempt g/l: <600

VOC g/l: <400

VOC lb/lb Solid: <0.90

VHAPs lb/lb Solid: <0.25

Note:

See individual compliance sheets for specific data

Suggested Uses:

Wood Primer

Mixing Ratio:

Reduce as required

Pot Life:

N/A

Application Viscosity:

Zahn #2 signature cup 25 – 30 seconds

Reducer: 803-1298

Retarder: 800-5328

Clean-up Solvent: N/A

Recommended Wet Film: 3 – 5 mils

Coverage:

341 sq. ft/gal at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

N/A

Viscosity:

95 KU at 77°F

Flash Point: -0.4° F (-20°C)

Density (lb/gal): 9.2

Solid (% by weight): 40%

Solid (% by volume): 21%

Shelf Life (months): 12

CHEMBASE Pigmented Primer

545-5104 Chembase White NC Pigmented Primer

Find distributor Trouver un distributeur

spec_description:

BACK

CHEMBASE Pigmented Primer

545-5104 Chembase White NC Pigmented Primer

spec_description:

Product codeCodes de produit
Product Codes:

545-5104

Product information

Product specificationsSpécifications du produit

Viscosity:

95 KU at 77°F

Flash Point: -0.4° F (-20°C)

Density (lb/gal): 9.2

Solid (% by weight): 40%

Solid (% by volume): 21%

Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_545-5104_Chembase_White_NC_Pigmented_Primer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap