VERDE UNICO Sealer

436-6601 ora Verde® Unico Sealer

Product Codes:

436-6601

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit paper prior to staining or coating. Sealer should be sanded with 280/320 grit paper prior to being coated. The sealer should be coated within eight hours of being sanded. When recoating, the previous coat of ora Verde Unico sealer must be sanded and the next coat applied within eight hours. Stain systems used under ora Verde Unico sealer are formulated to develop excellent grain definition. AkzoNobel recommends using Promatch® W/B Monocolor Spray Stains 824-50XX, Promatch Aqua Stains 824-51XX, Promatch Dye Stains 890-85XX or Promatch C-Mix Wipe Stains 825-90XX, 825-91XX.

General Information:

Oil stains must be avoided because they will interfere with the adhesion. When coating exotic woods (Teak, Rosewood, etc.) a barrier coat (tie-coat) should be applied before the sealer or base coat. See Product data sheet for 401-033 Isolante.

PDF Name: US-PIS_436-6601_ora_Verde_Unico_Sealer

Tack Free Time: 15 - 20 minutes

Files: US-PIS_436-6601_ora_Verde_Unico_Sealer.pdf

Dry to Sand : 1 hour

Dry to Stack: 4 hours

Tack Free Time: N/A

Dry to Sand: N/A

Dry to Stack: N/A

Note: N/A

spec_description:

ora Verde Unico Sealer is a new technology sealer offering a single component, low Formaldehyde and Isocyanate free finish. This product offers exceptional vertical hang and sanding properties and is designed to be used in conjunction with the ora Verde Unico Topcoat 436-66XX line.

spec_uses:

ora Verde Unico Sealer can be used in the following interior applications:

Cabinetry

Furniture

Millwork

Recreational

Building Products

VOC less exempt: <5.6

VOC lb/gal: <5.5

VOC less exempt g/l: <646

VOC g/l: <622

VOC lb/lb Solid: <2.06

VHAPs lb/lb Solid: <0.70

Note:

N/A

Suggested Uses:

Unico Sealer can be used in the following industries:

Cabinetry

Furniture

Millwork

Recreational

Building Products

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

Zahn #2 signature cup 22-24 seconds

Reducer: 803-1325 (5 -10% as needed)

Retarder: 800-5328 (2 - 3% maximum)

Clean-up Solvent: Acetone

Recommended Wet Film: 4 - 5 wet mils

Coverage:

Theoretical coverage - 320.49 (sq ft/dry mil @ 100% transfer efficiency)

Note application:

PRODUCT AND SYSTEM DRY FILM THICKNESS NOT TO EXCEED 4 MILS.

Viscosity:

Zahn #2 Signature cup 22 - 24 seconds at 77º F

Flash Point: -4º F (-20º C)

Density (lb/gal): 7.56

Solid (% by weight): 27.54 (+/- 1.00)

Solid (% by volume): 19.98 (+/- 1.00)

Shelf Life (months): 6

VERDE UNICO Sealer

436-6601 ora Verde® Unico Sealer

Find distributor Trouver un distributeur

spec_description:

BACK

VERDE UNICO Sealer

436-6601 ora Verde® Unico Sealer

spec_description:

Product codeCodes de produit
Product Codes:

436-6601

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 Signature cup 22 - 24 seconds at 77º F

Flash Point: -4º F (-20º C)

Density (lb/gal): 7.56

Solid (% by weight): 27.54 (+/- 1.00)

Solid (% by volume): 19.98 (+/- 1.00)

Shelf Life (months): 6

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_436-6601_ora_Verde_Unico_Sealer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap