AQUASET Pigmented Topcoat

423-27XX Aquaset WB Pigmented TC

Product Codes:

423-2710 Matte
423-2720 Low Gloss
423-2735 Satin
423-2750 Semi-Gloss

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit paper prior to coating. The recommended primer is Aquaprime 550-1600. Primer should be sanded with 280/320 grit paper prior to being coated. The Primer should be coated within four hours of being sanded for maximum adhesion. When recoating, the previous coat of Aquaset must be sanded and the next coat applied within four hours.

General Information:

Mix material before use. Add water to reduce if required and mix thoroughly. Apply by spray at 4 - 5 mils wet.

Aquaset must be agitated thoroughly at all times to ensure product consistency. Contact with metal surfaces should be avoided.

Maximum film build of total coating system must not exceed 4 mils dry.

The completed coating system should be checked for required properties prior to start-up of production.

PDF Name: US-PIS_423-27XX_Aquaset_WB_Pigmented_TC

Tack Free Time: 20 minutes

Files: US-PIS_423-27XX_Aquaset_WB_Pigmented_TC.pdf

Dry to Sand : 4 hours

Dry to Stack: 24 hours

Tack Free Time: 15 minutes

Dry to Sand: 15 minutes

Dry to Stack: 15 minutes

Note: N/A

spec_description:

Aquaset is a very durable white topcoat, formulated with a self-crosslinking polymer for maximum chemical resistance. Aquaset will give a smooth and hardwearing surface, resisting influence from alcohol, water, etc. Aquaset is non-yellowing and has very good light stability based on the type of resin used.

Aquaset meets Kitchen Cabinet Manufacturer Association (KCMA) standards.

spec_uses:

Aquaset is designed for interior applications such as kitchen cabinets, high build office furniture, residential furniture, molding, window and door frames, and other applications.

VOC less exempt: <2.00

VOC lb/gal: <0.86

VOC less exempt g/l: <235

VOC g/l: <105

VOC lb/lb Solid: <0.25

VHAPs lb/lb Solid: <0.006

Note:

See individual compliance sheets for specific data

Suggested Uses:

Wood Finish

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

Zahn #2 signature cup 40 seconds

Reducer: Use water as required. This product requires very little water to lower the viscosity.

Retarder: N/A

Clean-up Solvent: Use water when in liquid state, use water / Butyl Cellosolve 800-5742 when material is semi-dried

Recommended Wet Film: 4 - 5 wet mils

Coverage:

N/A

Note application:

N/A

Viscosity:

Zahn #2 signature cup 40 sec at 77° F

Flash Point: >140° F

Density (lb/gal): 9.65

Solid (% by weight): 42.3%

Solid (% by volume): 32.5%

Shelf Life (months): 12

AQUASET Pigmented Topcoat

423-27XX Aquaset WB Pigmented TC

Find distributor Trouver un distributeur

spec_description:

Aquaset meets Kitchen Cabinet Manufacturer Association (KCMA) standards.

BACK

AQUASET Pigmented Topcoat

423-27XX Aquaset WB Pigmented TC

spec_description:

Aquaset meets Kitchen Cabinet Manufacturer Association (KCMA) standards.

Product codeCodes de produit
Product Codes:

423-2710 Matte
423-2720 Low Gloss
423-2735 Satin
423-2750 Semi-Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 40 sec at 77° F

Flash Point: >140° F

Density (lb/gal): 9.65

Solid (% by weight): 42.3%

Solid (% by volume): 32.5%

Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_423-27XX_Aquaset_WB_Pigmented_TC.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap